Maintenance To Do

Items that need to be done

Oil Change
Front Brake Pads swapped


Monday, March 30, 2009

Cleared ABS

Followed the instructions from the previous post, made a wire, grounded it to one of the footpeg bolts, then inserted into the middle prong of the connector under the seat.

PHOTO here for record

Turned the ignition on, held down the ABS switch for 10 seconds, fault cleared, and has not come back. I have placed the trickle charger on because the heat of Texas has not hit us yet.

ABS Fault

I went for a ride yesterday, temp in the morning had hit 34 degrees, so the garage was cold most of the night. I waited for it to hit a balmy 62 degrees, to fill up the bike and put my second 6 oz of Chevron Techron in the bike. When I started it up it cranked slow but took with full choke.

I noticed the ABS lights flashing alternatively. This is not normal during pre-start test, but sometimes happens during first few minutes of ride, I usually ride a few minutes, stop put in Neutral, and re-start, clearing the fault. This did not happen, so I went ahead and rode to Texaco (which also has Techron in the fuel).

After fill up, still flashing ABS lights. The ABS clear button does work, but it only last for 4-5 mins.

When I got home I read the following article, and starting to rig up my own wire jumper.

http://www.largiader.com/abs/absfault.html

Here is a snipit

ABS2

ABS2 was used on K1100 from 1994 onwards, R1100RS/RT/GS/R, R1200C, and to 2000~2002 on the R1100S, R1150GS, and K12 models.* The K11 ABS2 uses the same two warning lights as ABS1: the ABS light and the bulb monitor light. On Oilheads and K12s, it has two distinct lights of its own. At key-on, the two lights will flash together and continue to do so until the self-test is complete (which doesn't happen until you start to ride away), at which time they extinguish. If the self-test fails, they will begin to flash alternately. The exact moment when the fault happens will help you know what caused it: if it happens before you start the engine it is an item that is tested at power-up. If it fails when you start the engine, it is almost certainly low battery voltage. And if it fails when you ride away, it's probably a modulator or a wheel speed sensor.

Sometimes ABS2 will fault without showing a fault code that you can read without the diagnostic computer.

Resetting ABS2 on early bike

  • Locate the diagnostic connector under the seat. Remove it from the blanking plug.
  • Insert one end of 20 cm wire into the middle socket of this connector.
  • Ground the other end firmly to a metal bolt in the area (and keep grounded).
  • Turn on ignition. You should see the lights flash alternately.
  • Hold ABS button down for about 8 seconds. The bottom ABS light will stay on, and the top one off.
  • Release the ABS button. If you have successfully reset the ABS, both ABS lights will come on. If you have failed to count to 8, or your ground is not good, the top ABS light will stay off.
  • Turn off ignition, remove wire.


Sunday, March 29, 2009

Something to Check

I noticed that my hazard light on the dashboard is not working, might need to open fairing and check connection.

Sunday, December 28, 2008

Ride Report


Today was a brisk, 40 degree morning here in Texas, sunny, slight breeze, no clouds. It was a great day to go out and stretch the legs of my new beemer. I decided not to do any specific route, but go where the tires take me. I circled a bit around Pilot Point, then made my way back to Prosper via Celina.

I have noticed for a while now, that there seems to be only two types of people on the road on Sunday mornings, church goers, and motorcyclists. The roads are not full of crazy commuters and it is usually to early for people to be clogging the roads trying to get to Home Depot or Target.

I stopped by the roadside to take a picture of the silver bullet. I have not taken any photos of it yet since purchasing. This was done with my cell phone, so the quality does not do the bike justice.

I did notice that 2nd and 3rd gear rev very high and surge a bit, and the forums I'm reading suggest that the motronic (http://www.ibmwr.org/r-tech/oilheads/R11-motronic)or throttle bodies over time need adjusting to get the fuel injection just right. A fuel injection cleaner like Chevron Techron Fuel System Cleaner, might help the problem, and can not hurt at this point.

Chevron Techron Fuel System Cleaner
http://www.amazon.com/Chevron-Techron-Fuel-System-Cleaner/dp/B00092893E





Tuesday, December 23, 2008

Battery Charger

Well, my first real experience with a "leap through technology" beemer. While trying to put my battery charger on, I soon discovered, not only is the battery tough to get to, but it a newer no maintenance free gel type battery, which is great,


but my standard Schumacher SEM-1562A battery charger will not charge the gel types.




So with a little research from the BMW MOA and talking to Ron, I quickly figured out that there is a Deltran Battery Charger made for BMW under the Battery Tender line or the Battery Doc charger will work with lead acid and gel type. The Battery Doc comes with the accessory plug included, so I bought one from Fly N Cycle for $37.00.

Battery Doc

BMW Owner News in Jan 2002 endorsed this product.

http://www.batterydoc.com/pressh.htm

Saturday, December 20, 2008

Researching Lubricants

Ok, I guess that title does sound funny, but in the process of reading the official BMW repair manual, they list some lubricants for general maintenance. Most of these are available in EMEA, but their equivalents need more research. I'm sure my local BMW dealer will sell me all of these at a heft price.

1) Retinax A, this is listed as the (taper) roller bearing grease in the repair manual, but I noticed is also used to lubricate the clutch cable and the adjustable windshield shaft. I used a basic lithium grease until I can find this product or its equivalent.



2) Staburags NBU 30 PTM, this is listed to grease the side stand. A google search produced articles suggesting alternatives such as Texistar or BMW red grease.










3) Brake Fluid DOT 4 quality classifications, e.g. ATE "SL" brake fluid, since this is done every year, I will most likely stick to Castrol or BMW only brake fluid.








4) Bosch ft 40v1, this grease was also recommended for airheads as a acid resistant battery terminal grease, some have suggested that Vaseline works also. This grease being German is hard to find in auto parts stores in the US. Moto bins has tubes of it.













5) Optimoly MP 3, and Optimoly TA. Moto bins online has both of these products listed as Castrol Optimol TA, and Castrol Optimol White Paste T, both being used for splines for final drive and clutch shaft.

Sunday, December 14, 2008

Oil Change




Oil Change and Filter was done 48,233 miles by previous owner.